Home > Temperature Control System > STB/E Infrared Thermometer

[Return Home] [Go Back]

STB/E Infrared Thermometer

Product Abstract:

Infrared Thermometer suitable for induction heating machine's solder, quenching,forging melting application


wechat:Joanna8608
Chat online wechat:Joanna8608
Product Description

STB/E Infrared Thermometer (Both type as options to select)

STB type Select:
This is machine special for the induction heating machine to design, and main suitable for the automatic solder, welding, brazing application.

 This is the infrared automatic adjust the power output of induction heating machine. For example, if the solder temperature need 800C, when the induction heating machine heat up to 800C, then the infrared automatic to adjust the machine's power output to always keep at 800C, the temperature will not up and will not down. Or you set 3S to reach 800C, maybe 3S at the same power output can reach 900C, at this time, the infrared will automatic power output, down a little power output, let's 3S up to 800C.

But this type need adjust our inside of machine then connect this infrared, and then can work together. The person who need know much our induction heating machine can know how to adjust our machine inside to connect it, generally speaking, need adjust by our engineer

Used closed-loop control output, control output power of the induction heating machine, so that the workpiece is heated temperature stabilized at a constant temperature set point , to achieve automatic constant temperature , heating time , constant temperature and  heating time heat . The alarm port can be used as warning lights and buzzer.

 Features:  

1 , Closed-loop control principle: The accurate thermostat in this way is the preferred method . The principle is: the machine to be controlled equipment power regulation to a given level as a reference (REF) , the minimum power level for the reference ( REF --- - ) , setting the temperature number and actual temperature digital treated by micro- The echelon comparison . Isolation device output corresponding voltage control induction heating machine output power , the output voltage limit between ref - REF +.

2 Automatic delay timer start options

The machine automatically delay start timer , there are two ways: one is start the machine and start the timer  at the same time, the other is : workpiece heated to the set temperature starts to timing, selected by the switch on the front panel , suitable for heating time , constant temperature heating time , such as melting, automatic welding, brazing, solder.

3 Automatic delay time scale selection

Factory standard full scale of 9.9 seconds and 99 seconds , selected by the switch on the front panel , the other scale is set according to customer requirements

4 Fiber optic sensing

Since the detector adapt to the ambient temperature is below 75 ° C , the use of fiber optic sensing . Detector placed in the main part , the probe tolerance to adapt to high temperatures and strong electromagnetic interference environment

5 Fully coaxial laser sighting

Laser direct measurement position is accurate , especially for small target precise positioning , they can always ON or OFF. The laser sighting switch without any operation , laser sighting will automatically enter turned off , the factory setting is 30 seconds unified , others set according to customer requirements

6 easy to operate

Temperature, time set by the respective plus↑ less ↓ key to set,  the machine is used as the measured temperature display digital tube , automatically display the set temperature when you set temperature , stop operation automatically return to displaying the measured temperature , if need confirm again the setting temperature , please press the dedicated keys .

 7 Parameter 

Model  

Measure temperature range 

structural pattern

STB9 2

0ºC-600ºC

Non fiber-optic 2 points aim

STB9

250-800ºC

Fiber-optic Coaxial aim

STB9 3

300ºC-1000ºC

Fiber-optic Coaxial aim

STB9

400-1200ºC

Fiber-optic Coaxial aim

STB9 4

400-1300ºC

Fiber-optic Coaxial aim

STB9 5

500-1500 ºC

Fiber-optic Coaxial aim

STB9 6

600-1800 ºC

Fiber-optic Coaxial aim

STB9 7

700-2200 ºC

Fiber-optic Coaxial aim

  Voltage: 220-240VAC  Power consumption< 10W

Distance  coefficient :75:1

Repeatability precision: 1 ºC 

Fiber length : 1.4M ( standard)

Time scale : 9.9 seconds , 99 seconds as option, others please according to request to set.

Timing start : start the machine start timing or heated to the set temperature starts timing as options

Laser sighting : any switch , such as laser sighting enable 30 seconds laser sighting switch without any operation , will automatically turn off (15 seconds for the standard set ) , others requirements according to customer to set.

Working temperature: Host ≤ 50 ºC Humidity : 10% -80%  Fiber - optic probe: temperature ≤ 150 ° C Humidity : 10% -80%

Dimension: Main part 240 ( L) x 180 ( W ) × 110mm ( H) mm fiber optic probe : diameter 20 x 90mm

STE Type select:

Main suitable for the quenching, hardening application and forging application.  
STE series main for hardening, quenching and forging application, this is main through set the upper limit temperature and lower limit temperature to contorl. For example: if you need hardening temperature is 800C, at this time you will set upper limit temperature is 800C, the lower limit temperature is 750C, so that when the heating temperature reach to 800C, the induction heating machine will stop it. When the workpiece lower 750C, the machine will heat again.
This series easy to connect to the induction heating machine, just let's the infrared wire connect to the our induction heating machine's switch foot signal interface, that's can control our induction heating machine.

Use the machine's main and auxiliary hot interface can control induction heating machine, stop heating when the workpiece is heated to the upper limit temperature - begin to heat when workpiece is below the lower limit temperature , that operating cycle control the workpiece temperature within the upper and lower limit temperature , automatic temperature control , and timing heating , constant temperature heating time.

 Also use the machine's main and auxiliary hot interface can respectively control two heat sources, to achieve three works temperature control , or other functions ( according to customer special requirements to set )

Features:
1 Relay switch signal output, switch current signal output, two models as options.
Relay switch output mode, the signal output device is reed relay, characterized can bear high voltage, withstand big current, string directly into the contactor control coil loop ,common use.
Switch current output mode , ( non-contact output way ) , the output signal standard is set to 12V 50MA ( or in connection according to customer requirements ) switch voltage signal , used for directly drive the solid-state relays, non-contact switch , due to the response of the solid-state relay fast , and it could get the best situation.
2  Automatic delay timer start way options
The machine automatically delay start timer , there are two ways: one is start the machine and start the timer at the same time, the other is : workpiece heated to the upper limit setting temperature begin to timing, selected by the switch on the front panel , suitable for quenching, hardening and so on.
3  Automatic delay time scale selection
Factory standard full scale of 9.9 seconds and 99 seconds , selected by the switch on the front panel , the other scale is set according to customer requirements
4  Fiber optic sensing
Since the detector adapt to the ambient temperature is below 75 ° C , the use of fiber optic sensing . Detector placed in the main part , the probe tolerance to adapt to high temperatures and strong electromagnetic interference environment
5  Fully coaxial laser sighting
Laser direct measurement position and with the actual testing point is fully same , they can ON or OFF at any time. The laser sighting switch without any operation , laser sighting will automatically enter turned off , and in order to reduce the power consumption , the factory setting is 30 seconds.
6  Easy to operate
Upper limit temperature and lower limit temperature, time set by the respective plus↑ less ↓ key to set, and keep continue display, but should remember the lower limit temperature should be can not higher than upper limit temperature. When the upper and lower limit is same, up the lower limit temperature unless, and also down the upper temperature, the lower limit temperature down automatic at the same time. If press  temperature difference delete one time, lower limit temperature =upper limited temperature automatic.
7 Parameter
 

Mode Temperature range Structure  model
STE280 250-800 ºC Line fiber-optic thermometer
STE412 400-1200 ºC Line fiber-optic thermometer
STE716 700-1600 ºC Line fiber-optic thermometer
STE1020 1000-2000 ºC Line fiber-optic thermometer
STE1527 1500-2700 Line fiber-optic thermometer

Voltage:  220VAC-240VAC   Power consumption < 10W
Distance  coefficient  :75:1
Repeatability precision: 1 ºC 
Fiber length : 1.4M ( standard)
Time scale : 9.9 seconds , 99 seconds as option, others please according to request to set.
Timing start : start the machine start timing or heated to the set temperature starts timing as options
Fully coaxial laser sighting : precise targeting, any switch , such as laser sighting enable 30 seconds laser sighting switch without any operation , will automatically turn off (30 seconds for the standard set ) , others requirements according to customer to set.
Working temperature: Host ≤ 50 ºC Humidity : 10% -80%  Fiber - optic probe: temperature ≤ 150 ° C Humidity : 10% -80%
Dimension: Main part 190 ( L) x 240 ( W ) × 115mm ( H) mm,  fiber optic probe : diameter 20 x 90mm
Pre-sale service:
1. recommend the most suitable machine for customers, according to their requirements. 
2. Inquiry and consulting support. 
3. Sample testing support. 
4. View our Factory.

In-sale service:
1. Strictly manufacture the machine, according to relevant technical standards.
2. Take run test, according to relevant equipment test run regulations.
3. Strictly check up the machine, before delivery
4. Delivery on time.

After-sale service:
1. Warranty time: Within 18 months from the date of delivering, 12months from date of receiving.
2. Within warranty all parts are free for customer, any fault caused by non-artificial reason, any quality problems such as design, manufacture, or procedure occurs, We shall provide replacement parts after detecting the faults.
3. If any big quality problems occurs out of the guarantee period, we will send maintenance
 technician to provide visiting service after checking with the customer and charge for a favorable price. 
5. We will provide a lifetime cost price to the buyer with the materials and spare parts used in system operation, equipment maintenance.
6. The above mentioned are only basic aftersale service requirements,we will make more promises related to quality assurance and operation guarantee.

Related Products
Ultrahigh Frequency Induction
High Frequency Induction Heating Machine
Super Audio Induction Heating
Medium Frequency Induction Heating Machine
Hot Sale Induction Heating Machine
-
Double Transfromer connect one Main Part
-
Hand type Connection Induction Heating Machine
-
Special Induction Heating Machine
Machine Line
-
Forging Furnace
-
Quenching Machine Line
Melting Furnace
-
Medium Frequency Melting Furnace
-
Small melting furnace
Medium Frequency Induction Power Supply
Water Cooling System
-
Chiller
-
Closed Cooling Tower
-
Open Cooling Tower
Temperature Control System

Contact Us

wechat:Joanna8608
Chat online